Mid-Drive vs Hub Motor: Which E-Bike Motor Is Better for Delivery Work?
Mid-drive or hub motor? How each works, torque, hills, chain wear, flats, repair costs and price, and why most delivery e-bikes use a rear geared hub motor.
Every e-bike motor sits in one of two places: inside a wheel hub or between the pedals. Reviews of mountain and commuter bikes usually crown the mid-drive. Delivery work is a different job: eight to ten hours a day, dozens of starts from a red light, a heavy bag on the rack and a bike that has to roll again tomorrow morning. Below is how each motor works, where each one wins, what breaks and what it costs, and why nearly every rental and delivery e-bike, including ours, runs on a rear hub motor.
The short answer
A mid-drive motor sits at the cranks and drives the chain, so it uses the bike's gears. It climbs steep hills better, feels more natural and usually comes on more expensive bikes. A hub motor sits in the center of the front or rear wheel and pushes the wheel directly. It is cheaper, simpler and leaves the chain alone.
For delivery riders, a rear geared hub motor with a throttle is usually the better tool: it costs less to buy and to keep running, doesn't eat chains and sprockets, and gives you a push from behind when you start with a load. A mid-drive makes sense if your routes are very hilly, you pedal hard and you are ready to replace drivetrain parts more often.
How a hub motor works
A hub motor is built into the center of the wheel. There are two kinds:
- Geared hub. A small fast-spinning motor drives the wheel through a set of internal planetary gears. This is the most common type: it's lighter, cheaper and better at climbing than a gearless hub of the same size. When you stop powering it, a clutch lets the wheel roll freely.
- Direct-drive (gearless) hub. The motor is the hub itself, with no moving parts besides the bearings. It's quiet and very long-lasting, and it can recharge the battery a little when you brake (regenerative braking). It's also heavier: roughly 5–11 kg, against 2–4 kg for a geared hub.
Most delivery and rental e-bikes in the US use a rear geared hub in the 500–750 W range. A hub motor works on its own, separately from the chain and gears: the motor turns the wheel, your legs turn the chain, and the two meet only at the rear wheel.
How a mid-drive motor works
A mid-drive is mounted at the bottom bracket, where the cranks are. It turns the chainring, so its power goes through the chain and the rear gears, just like your legs do. That is its big advantage: in a low gear even a modest motor turns into a lot of torque at the wheel, which is why mid-drives climb so well.
Typical numbers from the big brands:
| Motor | Type | Max torque | Notes |
|---|---|---|---|
| Bosch Performance Line CX | Mid-drive | 85 Nm | 600 W peak, about 6.4 lb |
| Bosch Cargo Line | Mid-drive | 85 Nm (newer versions up to 100 Nm) | Used on cargo bikes like the Tern GSD |
| Shimano EP801 | Mid-drive | 85 Nm | Common on e-MTBs |
| Bafang BBS02 (kit) | Mid-drive | about 120 Nm | 750 W aftermarket kit |
| Bafang BBSHD (kit) | Mid-drive | about 160 Nm | 1,000 W, over the federal 750 W definition |
| Zoomo One delivery bike | Rear hub | 45 Nm | Built for delivery fleets |
Torque numbers aren't directly comparable between the two types: a mid-drive's figure is measured at the cranks and then multiplied by the gears, while a hub's figure is applied straight to the wheel.
Mid-drives also keep the weight low and in the middle of the frame, and most of them use a torque sensor that reads how hard you push, which feels natural. Many premium mid-drive bikes are pedal-assist only, while hub-motor bikes usually come with a throttle. More on sensors in our guide to what pedal assist is and whether you need it.
Mid-drive vs hub motor: side by side
| Rear geared hub | Mid-drive | |
|---|---|---|
| Where it sits | Rear wheel | At the cranks |
| Uses the bike's gears | No | Yes |
| Steep hills | Good, can heat up on long steep climbs | Best |
| Starts from a stop with a load | Strong push from the rear wheel | Strong, if you're in a low gear |
| Throttle | Common | Less common on big-brand bikes |
| Chain and sprocket wear | Normal | Much faster |
| Rear flat tire | More work (motor cable, axle nuts) | Same as a regular bike |
| Price of the bike | Lower | Often $1,000–2,000 higher |
| Repair if the motor fails | Cheaper | More expensive |
Hills
This is where the mid-drive clearly wins. Because it shifts with you, the motor stays in its efficient speed range even on a steep, slow climb. A hub motor has one fixed ratio: on a long steep climb at low speed it works hard, gets less efficient and can overheat.
For city delivery this matters less than reviews suggest. A 500–750 W geared hub handles bridges, overpasses and the short hills of Manhattan, Philadelphia or DC without trouble, especially with a throttle. If your zone is San Francisco's steepest hills and you pedal a lot, a mid-drive has a real edge. Riders on forums still argue about it: some say a 750 W hub with sensible gearing climbs as well as a 250 W mid-drive.
Chain and drivetrain wear
This is the mid-drive's biggest downside for a working bike. All of the motor's power, hundreds of watts for hours, goes through your chain, sprockets and derailleur. Electrek calls mid-drives "brutal on your drive system" and names snapped chains as probably the number one maintenance problem.
How long parts last depends on how you ride, so mileage estimates vary a lot, from about 500 to several thousand miles per chain. Practical rules from shops:
- Check chain stretch with a chain checker about every 200 miles and replace the chain at 0.5% stretch (0.4% if you want to save the cassette).
- A well-kept cassette survives about two or three chains.
- Ease off the pedals for a moment when you shift. Bosch even added a system that pauses the motor for a split second during a shift, specifically to reduce drivetrain wear.
On a hub-motor bike the motor never pulls on the chain, so the chain lasts as long as on a regular bike. And if the chain does break, a bike with a hub motor and a throttle can still get you home. A mid-drive with a broken chain can't move at all.
Flats and wheel work
Here the hub motor loses. Fixing a rear flat on a hub-drive bike means taking out the battery, unplugging the motor cable near the axle, freeing the cable clips and removing a heavier wheel held by axle nuts. Schwinn's own guide walks through those extra steps. At a shop, a rear flat on a hub bike typically costs $20–30 more. On a mid-drive bike, a flat is an ordinary bike flat.
Puncture-resistant tires take most of the pain out of this, which is why delivery bikes are usually built with them.
Price and repair costs
Hub motors are much cheaper to make, and that shows up everywhere:
- Complete bikes. A hub-motor e-bike often costs $1,000–2,000 less than a similar mid-drive model.
- Conversion kits. A Bafang BBSHD mid-drive kit runs about $670–695, motor only. Geared hub kits start around $375–455.
- Upkeep. Repair shops estimate mid-drive drivetrain upkeep adds roughly $100–200 a year, and that hub bikes cost 30–50% less to maintain over time. A new chain is about $30–80; e-bike cassettes can cost far more.
- Motor failure. Labor to replace either motor runs about $100–250 at a shop, but a mid-drive unit itself is more expensive to replace out of warranty.
The weak spot of a geared hub is its internal nylon gears, which can wear or strip after years of heavy use. The fix is a gear set or a new motor, not a new drivetrain.
Why delivery bikes use rear hub motors
Look at rental and delivery fleets and you'll see the same choice again and again: a rear geared hub, a throttle and a simple cadence sensor. We asked our product team why every Whizz bike is built that way. Their answer came down to three things:
- Cost. Mid-drive motors are more expensive, and that ends up in the rider's price.
- Drivetrain wear. A mid-drive wears out the chain, freewheel and sprockets faster. For a courier that means more frequent part swaps, and a bike with a worn drivetrain barely rides. That's a lost shift.
- The push from behind. A rear hub pushes the bike forward from the rear wheel. That matters when you start from a stop with a full bag or box on the rack, dozens of times a day.
Add the throttle, which lets you pull away from a light before your foot is even on the pedal, and the hub motor fits stop-and-go city work better than a mid-drive.
What about the law?
The law doesn't care where the motor sits. Under federal law a "low-speed electric bicycle" has a motor of less than 750 W and a motor-only top speed under 20 mph. New York State uses the same 750 W limit for all e-bike classes, and New York City adds a citywide 15 mph speed limit for e-bikes. A mid-drive and a hub motor are treated the same, as long as the power and speed fit the class. Watch out for kits advertised at 1,000 W and more: they exceed the 750 W definition. See our guide to e-bike laws for delivery riders in Washington DC for how local rules add up.
What motors are on Whizz e-bikes?
All Whizz e-bikes use a rear geared hub motor, a throttle and five levels of pedal assist:
| Model | Motor | Power |
|---|---|---|
| Storm-2 | Rear geared hub | 500 W nominal, 750 W peak |
| Thunder | Rear geared hub | 500 W nominal, 750 W peak |
| Monster | Rear geared hub | 750 W |
Nominal power is what the motor can deliver continuously; peak power is the short burst you get when starting or climbing.
Frequently asked questions
Is a mid-drive better than a hub motor?
It depends on the riding. A mid-drive is better for steep hills, off-road riding and a natural, bike-like feel. A hub motor is better for low price, low maintenance and stop-and-go city riding with a throttle, which is why most delivery e-bikes use one.
Which is better for hills, a mid-drive or a hub motor?
A mid-drive, because it uses the bike's gears and stays efficient at low speed. A 500–750 W geared hub motor still handles city bridges and short hills well, especially with a throttle, but it can heat up on long, steep climbs.
Which lasts longer, a hub motor or a mid-drive?
There's no clear winner for the motor itself. Hub motors are sealed and simple, and a direct-drive hub has almost nothing to wear out. Mid-drives are well built, but they wear out chains and sprockets much faster, so the bike as a whole usually needs more parts and more shop time.
Are hub motors harder to maintain?
Mostly no. The motor itself needs little attention. The only extra work is with the rear wheel: fixing a rear flat takes longer because you have to unplug the motor cable and remove a heavier wheel.
Can you put a mid-drive on a delivery e-bike?
You can convert a regular bike with a mid-drive kit, but it won't turn a hub-motor e-bike into a mid-drive one: the frame, battery and controller are built around the hub motor. Changing the electrical system of a certified e-bike can also void its UL 2849 certification.
The bottom line
A mid-drive is the better engine on paper: more torque on hills, a more natural ride, better balance. For a bike that works a full shift every day, the rear hub motor is the better tool: cheaper to buy, cheaper to run, easy on the chain, with a throttle and a push from behind for every start. Choose a mid-drive if you climb serious hills and pedal hard; choose a rear geared hub if the bike is your job.
Ride a delivery e-bike built around a rear hub motor. The Whizz Storm-2 and Thunder come with a geared hub motor, a throttle, hydraulic brakes and live GPS tracking, with repairs at Whizz hubs, on Rent-to-Own with no credit check. See Whizz e-bikes.
Motor specs and prices were checked on November 16, 2026. Manufacturers update their motors often; confirm current specs before you buy.